The Art Of Tying Rockport Boat Shoes: A Step-By-Step Guide

Rockport boat shoes are notoriously difficult to tie, especially if they have leather laces. A standard shoelace knot may not be enough to keep the laces from coming loose. There are several ways to tie boat shoes, including the barrel knot, the tassel knot, the chain knot, the surgeon's knot, and the fishtail knot.

How to tie a barrel knot

To tie a barrel knot for your Rockport boat shoes, follow these steps:

Firstly, start by making a loop and crossing the lace in front of the shoe. Then, take the other lace and make a second loop. You should then lace the second loop through the first one from the back. Pull the loops tightly and then repeat this step twice more.

Next, you should tuck the end of the lace into the loop at the end of each knot. Fold the lace to make a loop and then give it a twist. Wrap the other lace around your loop five times. Run the end of your lace through the top of the loop and pull the end of the lace while pushing the knot to tighten it.

If you want to clean up the look of the knot, trim off any extra lace.

Finally, make a square knot by crossing your lace left over right and then right over left. Form a loop with one of the laces and tie the other lace around the loop three times. Tuck in the end and tighten.

How to tie a tassel knot

Tying a tassel knot on your Rockport boat shoes will give them a neat and tidy look. Here is a step-by-step guide on how to do it:

First, cross the laces to create an "X" by placing the left lace on top of the right one. Then, take the left lace and bring it under the right one. Pull the laces in opposite directions.

Next, you will tie a square knot. Take the left lace in your left hand and the right lace in your right hand, ensuring the right lace is on top of the left one. Bring the right lace under and then over the left lace. Repeat the process with the left lace, bringing it under and then over the right lace. Pull the laces tightly and you will have a secure square knot.

Now, form a loop with the left lace. Fold the lace over itself at the base of the square knot, creating a loop of about 1 inch in length. Hold the base of the loop between the thumb and index finger of your non-dominant hand.

With your dominant hand, grab the tail of the lace and wrap it tightly around the loop 2 to 3 times. Thread the end of the lace through the loop and pull tightly.

Repeat the process with the right lace, creating a mirror image of the tassel on the other side. Trim the ends of the laces if they are too long.

And there you have it! A neat tassel knot for your Rockport boat shoes. Repeat the process for the other shoe, and you're all set!

How to tie a chain knot

To tie a chain knot, follow these steps:

• Using one hand, take the left lace and, with the other hand, create a 1/2-inch loop in the middle of the lace. Hold this loop with your left hand.
• On the same lace, make a second 1/2-inch loop and insert it into the first loop. Tighten the second loop by pulling.
• Continue to make another loop and insert it into the second loop. You can repeat this step depending on the lace's length.
• Keep the final loop in one hand and use the other hand to put the end of the lace through the final loop and tighten.
• Do the same with the right lace to tie a chain knot.
• Pull the left chain to the right and tuck the end of the left lace into the shoe. Then, do the same with the right chain, placing it above the left chain.

How to tie a surgeon's knot

To tie a surgeon's knot for your Rockport boat shoes, follow these steps:

First, start by making a loop and crossing the lace in front of the shoe. Take the other lace and make a second loop. Cross the left shoelace over the right, then wrap the left lace over and under the right before pulling both laces in opposite directions.

Next, take the left lace and form a one-inch loop next to the starting knot. Bring the right lace in front of the loop and circle it around the base. Now, make a loop out of the right lace and insert it into the circle, pulling it through loosely. This is essentially just a normal shoelace knot.

Then, wrap the right loop over and around the left loop, inserting it into the circle again. Take one loop in each hand and pull them tightly in opposite directions.

Finally, tuck in the ends and tighten the knot. This will keep your boat shoes secure, and the right knot can also be very eye-catching with a nice, clean pair of shoes.

How to tie a fishtail knot

To tie a fishtail knot for your Rockport boat shoes, follow these steps:

Firstly, it is important to note that boat shoes are notoriously difficult to tie, especially if they have leather laces. Leather laces will come loose from normal knots very easily, so you will need to learn some more complicated knots.

Begin by making a loop and crossing the lace in front of the shoe. Take the other lace and make a second loop. Then, lace the second loop through the first one from the back. Pull the loop tightly and then repeat twice more.

Next, you will need to tuck the end of the lace into the loop at the end of each knot. Fold the lace to make a loop and then twist it. Wrap the other lace around your loop five times. Run the end of your lease through the top of the loop and pull the end of the lace while pushing the knot to tighten it.

If you want to clean it up, trim off the extra lace. Make a square knot by crossing your lace left over right and then right over left over left. Form a loop with one of the laces. Tie the other lace around the loop three times. Tuck in the end and tighten it.

Finally, cross the left shoelace over the right. Then wrap the left lace over and under the right before pulling both laces in opposite directions. Take the left lace and form a one-inch loop next to the starting knot. Bring the right lace in front of the loop and circle it around the base of the loop. Make a loop out of the right lace and insert it into the circle, pulling it through loosely. This is essentially just a normal shoelace knot. Wrap the right loop over and then around the left loop and insert it into the circle again. Take one loop in each hand and pull them tightly in opposite directions.

Frequently asked questions